Back to the main page Back to category Jet Boats
boat details
1973 Slickcraft
Estimated price for orientation: 3 650 $
Category: Jet Boats
Class:
Description Condition: Used Year: 1973 Make: Slickcraft
Up for auction is the result of a 4 year project. I have a 1973 Slickcraft that has been converted to a jet drive with a small block 355 Chevy. Just about everything in the entire boat was replaced and there are hundreds of hours of work. The boat runs great, sounds incredible, and does 50 mph flat out. This is a unique boat with shallow water capabilities that is well built and was just finished this past summer. Please ask any questions and I encourage local inspection. The boat is also for sale locally.A $500 non-refundable deposit is due within 48hrs of auction end. Boat:
The boat was completely gutted down to the bare fiberglass hull.
- New stringers and floor
- USCG required flotation foam
- New seats
- New wiring harness
- New gauges
- New steering assembly and cable
- New poly 33 gal fuel tank
- New trim tabsEngine:
The engine is a 70s small block Chevy that is been bored out to 355ci.
- 4 bolt main block
- Rebuilt Vortec 906 heads - S/S valves, upgraded valve springs, studs, guide plates
- Comp Xtreme Marine 262 cam
- Comp Roller Tip Rockers
- Edlebrock RPM Air Gap intake
- Edelbrock Marine 600 cfm carb (USCG approved)
- PerTronix Ignitor II Distributor - Marine (USCG approved)
- FelPro gaskets & ARP Head Bolts
- Double roller timing chain
- New water pump
- New mainfolds and risers
- Closed loop cooling system with heat exchanger and flushing portJet Drive:
Jacuzzi YJ Pump
Rebuilt with Energizer kit - (converts YJ pump from low pressure to high pressure - $2,000 Kit)
Custom cut B/C impeller
New Hydraulic place diverter kit
Rudder for slow speed steering
Sport intake loaderTrailer:
Venture bunk trailer 3000lb capacity
All new LED lights and wiring
New tires
New bearings
New winch/strap
On Feb-05-17 at 14:27:18 PST, seller added the following information:Please Note the following additional clarifications:- There is the original alum rub rail with rubber molding included with the boat.- The Venture trailer is a single axle galvanized trailer.
Description
| Condition: | Used | Year: | 1973 |
| Make: | Slickcraft |
Up for auction is the result of a 4 year project. I have a 1973 Slickcraft that has been converted to a jet drive with a small block 355 Chevy. Just about everything in the entire boat was replaced and there are hundreds of hours of work. The boat runs great, sounds incredible, and does 50 mph flat out. This is a unique boat with shallow water capabilities that is well built and was just finished this past summer. Please ask any questions and I encourage local inspection. The boat is also for sale locally.
On Feb-05-17 at 14:27:18 PST, seller added the following information:Please Note the following additional clarifications:- There is the original alum rub rail with rubber molding included with the boat.- The Venture trailer is a single axle galvanized trailer.
A $500 non-refundable deposit is due within 48hrs of auction end. Boat:
The boat was completely gutted down to the bare fiberglass hull.
- New stringers and floor
- USCG required flotation foam
- New seats
- New wiring harness
- New gauges
- New steering assembly and cable
- New poly 33 gal fuel tank
- New trim tabsEngine:
The engine is a 70s small block Chevy that is been bored out to 355ci.
- 4 bolt main block
- Rebuilt Vortec 906 heads - S/S valves, upgraded valve springs, studs, guide plates
- Comp Xtreme Marine 262 cam
- Comp Roller Tip Rockers
- Edlebrock RPM Air Gap intake
- Edelbrock Marine 600 cfm carb (USCG approved)
- PerTronix Ignitor II Distributor - Marine (USCG approved)
- FelPro gaskets & ARP Head Bolts
- Double roller timing chain
- New water pump
- New mainfolds and risers
- Closed loop cooling system with heat exchanger and flushing portJet Drive:
Jacuzzi YJ Pump
Rebuilt with Energizer kit - (converts YJ pump from low pressure to high pressure - $2,000 Kit)
Custom cut B/C impeller
New Hydraulic place diverter kit
Rudder for slow speed steering
Sport intake loaderTrailer:
Venture bunk trailer 3000lb capacity
All new LED lights and wiring
New tires
New bearings
New winch/strap
The boat was completely gutted down to the bare fiberglass hull.
- New stringers and floor
- USCG required flotation foam
- New seats
- New wiring harness
- New gauges
- New steering assembly and cable
- New poly 33 gal fuel tank
- New trim tabsEngine:
The engine is a 70s small block Chevy that is been bored out to 355ci.
- 4 bolt main block
- Rebuilt Vortec 906 heads - S/S valves, upgraded valve springs, studs, guide plates
- Comp Xtreme Marine 262 cam
- Comp Roller Tip Rockers
- Edlebrock RPM Air Gap intake
- Edelbrock Marine 600 cfm carb (USCG approved)
- PerTronix Ignitor II Distributor - Marine (USCG approved)
- FelPro gaskets & ARP Head Bolts
- Double roller timing chain
- New water pump
- New mainfolds and risers
- Closed loop cooling system with heat exchanger and flushing portJet Drive:
Jacuzzi YJ Pump
Rebuilt with Energizer kit - (converts YJ pump from low pressure to high pressure - $2,000 Kit)
Custom cut B/C impeller
New Hydraulic place diverter kit
Rudder for slow speed steering
Sport intake loaderTrailer:
Venture bunk trailer 3000lb capacity
All new LED lights and wiring
New tires
New bearings
New winch/strap
On Feb-05-17 at 14:27:18 PST, seller added the following information:Please Note the following additional clarifications:- There is the original alum rub rail with rubber molding included with the boat.- The Venture trailer is a single axle galvanized trailer.