Back to the main page Back to category Narrowboats or Canalboats

boat details

Teal 23ft Centre Cockpit Cabin Cruiser & 2600kg Max Load / Twin Axle Trailer

Estimated price for orientation: 3 995 $

Category: Narrowboats or Canalboats
Class:











Description
Condition: Used: An item that has been previously used. See the seller’s listing for full details and description of any imperfections. See all condition definitions- opens in a new window or tab ... Read moreabout the condition  


Teal 23ft Centre Cockpit Cabin Cruiser Boat Project / Basically New Twin Axle 2600kg Mass Load TrailerRiver / CanalIf you bid on this boat it is to buy!! You can not arrive to collect and say it is not as described,
I am happy and infact encourage viewings first!! I expect a £200 paypal payment to be made by the winning
bidder within 24hrs and expect the boat to be collected with 14days of bid end.You will need a 4x4 or a large Van / Vehicle with a relative towing capacity to collect.The Boat is stored on a Farm Near Arundel West Sussex.The Boat trailer has the light board but you will need to bring number plates etc.The Teal 23ft Boat Cost me £1700 ( Original Receipt of purchase available )The Boat comes with a Yamaha 4 stroke 9.9 hp Engine ( Can not currently test since electrical COntrol Panel currently removed.
Engine is all fitted with Steering And gear Lever all in place and working so know major work required.
Electrical Ignition all connected back to engine just needs mount re screwing onto ops panel and ops panel made live again.
I have the Ignition Key comes in sale.
Engine was tested last year before Ops panel removed and on purchase with no problems and the person I had brought the boat from said it had done
minimum boat miles and see pic as all looks very clean, I would advise a service and check over but have no doubts
the Engine will all be fine) Also this engine charges the battery when running and I saw the console
volt meter increase when engine on and running like how the alternator does on a car. There is a photocopied Service manual for
this Engine / Yamaha F99Ae  / 6G8 L 403293Having to Sell due to changes in work situation.The Boat comes on a Basically brand New Twin Axle SBS R4 2600B Boat Trailer (2600KG Mass Load)
Information / Service Manual / Cert of conformity paper work all supplied.The Trailer was purchased brand new in Nov 2013 delivered to me in Jan 2014 in Redhill (where I worked at the time) direct from Manufacturer
and from Redhill I took trailer to Norwich to collect boat and then to my boat storage in Arundel and other than moving about in yard to keep things moving
every now and then that is the only mileage this trailer has done.SBS current same type twin axle trailer (sbstrailers.com) is the R4 /2600EL
priced at £4081.25 + VAT + Delivery Totaling over £5000.This Boat still has a fair amount of work needed to be done to finish, I would advise you have
a good DIY standard and some basic low voltage electrical know how would help / Basic Boat know how.
At minimum damn good clean It will need all outside and inside sanding and painting, Windows fitted, Electrics, Plumbing,
All upholstery re installing, Canopy attached it will need curtains made and fitted for windows.Will be great when it is all done. The great thing with a centre cockpit is you basically have 2 private sleeping areas,
Will comfortably sleep 4 minimum. 2 in front 2 in rear, has a sink area and a little toilet area for
a cassette type toilet.The boat does not have a boat safety certificate.Work DoneI have spent many days (30 upwards) working on this boat.Since Purchase I have stripped out all upholstery, Electrics, Plumbing.
A few parts of the floor were weak and I have strengthened these and the floor is now solid.
A couple of areas of the seating area were weak and they have all now been strengthened.
I have cut a centre piece of wood to go between the front seating areas to make a larger sleeping area.
I have cut a centre piece of wood in the rear to improve sleeping area and it also doubles as the table.
I have cut new pieces of wood for the storage / seating opening areas
I have made some flat areas in under seat storage so water tanks can sit flat.
I have cut a couple of new flooring sections.
I have cut new rear window wooden surround sections.
I have made a storage area for the front centre section piece of wood when not used.
I have fitted new bilge pumps (atleast 2 in front and 2 in rear with all new hose and on the water
outlet holes I have fitted one way flow valves.
I have fixed some low power 12v lights to cabins and run cable back to cockpit
I have fitted 2 waterproof speakers to rear cabin.
I have cut new pieces of ply wood which need to be covered in a thin foam and a fabric, these plywood
pieces are to go on the rear of the seating areas.
I have removed all front windows as they were in very poor condition and all the seals have perished and
the perspex and frosted.
I have had the Captains chair Re upholstered over £150 ( New upholstered Seat and Back parts needs fitting
to Chair Brackets )
Original Seating cushions included in sale but I have not cut new cushions for the newly added centre
wood pieces added as above.
The Switch Console needs sanding painting / Switches screwed into holes (New Switches Supplied) and wires connecting.
I have fitted a car stereo in the front to attach to speakers but it did get wet so cant promise that
stereo will be working but it is fitted into a stereo mount so easy to remove and replace.Additional Purchases I have made since boat purchase and are all included in sale ( Still need to be installed / Wired / plumbed etc etc )The two large metal front sliding side glass windows were stripped with all new rubber seals fitted
at a cost of about £125 each window. All the other frosted perspex fixed windows have had new perspex pieces
cut and still have protective film over them again further £££. I have also purchased all the rubber window seal to go between
windows and the fibre glass at a cost of over £180 (Receipt available)
I have had a new centre cockpit canopy made at a cost of over £400.
Rubber Gas hose included £
Gas Valve Switches all New £
Bubble Gas Tester included Approx £60 from memory.
2 x Water Tanks New £
Low wattage fridge £
12Volt new Invertor £
New Switches to be fitted to switch console £
All new NAV lights £
New Horn £
Solar Controller £
Handles Hinges £
Fasteners £
External Gas Bottle Basket holder £   (Also Fitted externally already)
Jerry Can external Basket Holder £ (Also Fitted externally already)
Jerry Can £
Marine Compass £
Marine Paint £
Anti Slip Granule Sachets to add to paint on decking areas £
Jubilee clips, Hose Clips £
Carbon Monoxide and Smoke Detector Alarm) £
Used FLavel Boat Oven cost over £150 ( I have fitted this to a gas bottle to test and all working
oven and grill and hob )
Used and all tested working Catalytic Gas Heater £
comes with a leisure battery.
Wires, Electrical Clamps,
Industrial Grade Anti Slip Laminant FLooring ( I thought this would be better then Carpet ) £150 will cover
all the floor front centre and rear.So About £10 000 Spent Plus my labour of 30 + days ( Good Luck )